openwrt/target/linux/ar71xx/image/Makefile, branch master

ar71xx: drop target

2020-08-30T20:18:35Z

This target has been mostly replaced by ath79 and won't be included in the upcoming release anymore. Finally put it to rest. This also removes all references in packages, tools, etc. as well as the uboot-ar71xx and vsc73x5-ucode packages. Signed-off-by: Adrian Schmutzler

build: image: move IMAGE_SIZE to image.mk

2020-03-11T17:25:06Z

IMAGE_SIZE is widely used in many targets. Declare it in the default template to clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally from the previously defined device. While at it, remove duplicate KERNEL_SIZE declaration. Signed-off-by: Sungbo Eo

ar71xx: Move some targets to tiny

2018-10-17T16:02:16Z

Recent changes on ar71xx (switch to 4.14, memory compaction, ...) cause an increase in kernel size, making it too big for some devices. Move these devices to the tiny target, where kernel symbols and optimization for speed are disabled, reducing the kernel size. Devices: - EnGenius ENS202EXT - OCEDO Koala Compile-tested targets: - ar71xx->generic->default - ar71xx->smallFlash->Default Signed-off-by: Koen Vandeputte

ar71xx: move boards to tiny subtarget

2018-07-12T16:15:19Z

Move boards to the tiny subtarget which break the build if the kernel is set to "Optimize for performance". Signed-off-by: Mathias Kresin

ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices

2018-01-13T18:54:45Z

This new subtarget sets the small_flash flag and removes unused kernel configuration. small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default configuration; removing unneeded hardware support from ar71xx/tiny saves another ~18KB (both after LZMA). Signed-off-by: Matthias Schiffer

ar71xx/generic: add generic- prefix to vendor-specific image Makefile snippets

2018-01-13T18:54:45Z

Signed-off-by: Matthias Schiffer

ar71xx: image: use simply expanded variables

2017-06-11T19:32:17Z

Signed-off-by: Piotr Dymacz

ar71xx: image: keep custom Build/* functions in separate files

2017-06-11T19:22:46Z

Most of the custom Build/* functions in ar71xx target are rarely used by image building code for devices from more than one subtarget. As they don't need to be always included, move them to corresponding *.mk files. Signed-off-by: Piotr Dymacz

ar71xx: add support for EnGenius ENS202EXT

2017-05-30T12:15:25Z

EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer

ar71xx: convert mikrotik routerboard support to UBI

2017-01-16T19:40:12Z

Remove the wget2nand script, drop the need for manual installation, use sysupgrade instead. There are now two different NAND images, one for 64 MiB flashes, the other for >= 128 MiB Signed-off-by: Felix Fietkau