openwrt, branch v23.05.0-rc3

OpenWrt v23.05.0-rc3: adjust config defaults

2023-08-20T19:50:15Z

Signed-off-by: Hauke Mehrtens

hostapd: revert upstream commit to fix #13156

2023-08-19T14:01:06Z

Commit e978072baaca ("Do prune_association only after the STA is authorized") causes issues when an STA roams from one interface to another interface on the same PHY. The mt7915 driver is not able to handle this properly. While the commits fixes a DoS, there are other devices and drivers with the same limitation, so revert to the orginal behavior for now, until we have a better solution in place. Fixes: #13156 Signed-off-by: Stijn Tintel (cherry picked from commit 324673914d42f5fb9b70cc73e955117828b99f3b)

armsr: add kmod-sfp to default device profile

2023-08-19T13:11:55Z

This brings the 23.05 branch into parity with the main. kmod-sfp was in the main branch profile but not the 23.05 version. Signed-off-by: Mathew McBride

armsr: armv8: fix invalid symbol value for FSL_ENETC_QOS

2023-08-19T13:11:55Z

The kernel FSL_ENETC_QOS option is only a compile time option, it does not result in a separate module being built. Set it to 'y' to resolve a warning from the kernel compile: .config:2654:warning: symbol value 'm' invalid for FSL_ENETC_QOS Signed-off-by: Mathew McBride Fixes: c3151b6f045 ("armvirt: 64: add support for other SystemReady-compatible vendors") (cherry picked from commit 7770d08e2bd28c9c0dc0b3dc0aaf74074ad5772a)

armsr: armv8: package and select MDIO driver for Thunder SoC's

2023-08-19T13:11:55Z

This MDIO driver was already being built, but not installed due to being selected by the ThunderX Ethernet driver. Signed-off-by: Mathew McBride (cherry picked from commit 0018b335313ec7d866bf9e22273b620759e29598)

armsr: add Marvell (Cavium) ThunderX2 network driver

2023-08-19T13:11:55Z

The initial armv8 module incorrectly labelled the Thunder(v1) as supporting the ThunderX2, when they have different drivers. Add kmod-octeon-tx2 to support the newer devices. Signed-off-by: Mathew McBride (cherry picked from commit 7c5bdff9c472a3f008ac15cc1ccb81cd23b20e1f)

armsr: armv8: add bcmgenet (Raspberry Pi 4 GENET) to profile

2023-08-19T13:11:55Z

kmod-bcmgenet is needed for Ethernet support on the Raspberry Pi 4. Signed-off-by: Mathew McBride (cherry picked from commit 911ee97774d2542300916f0e2763aa54c2a4dff1)

armsr: armv8: add Broadcom GENET and MDIO modules

2023-08-19T13:11:55Z

These are used by common Broadcom SoC's like the BCM2711 (RPi4) and iProc network processor. Tested on the RPi4B using the Raspberry Pi UEFI+ACPI firmware[1]. Signed-off-by: Mathew McBride [1] - https://github.com/pftf/RPi4 (cherry picked from commit 27ca83c6270a4cc6922cdae82bb5c01e4e2d1d22)

armsr: armv8: enable AHCI/SATA controllers for mvebu,qoriq,juno

2023-08-19T13:11:55Z

When comparing the generated OpenWrt .config to the Linux arm64 defconfig, I noticed these SATA controllers were not included. As they may be used as a boot drive, they should be built into the kernel. CONFIG_SATA_MVEBU is for Marvell platforms. CONFIG_SATA_QORIQ is for NXP Layerscape. CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux kernel commit d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA controller"). Signed-off-by: Mathew McBride (23.05/5.15 version of commit 9cb173e9f18da2530c3570479567d8130b05e5f8)

armsr: armv8: synchronize PCIE related options with arm64 defconfig

2023-08-19T13:11:55Z

This turns on various PCI related options which are enabled in the Linux kernel arch/arm64/configs/defconfig but not yet in the OpenWrt config. Signed-off-by: Mathew McBride (23.05/5.15 version of commit 15d3536c9deb2927c9a39350c6fa2e59f859df2a)